preliminary EUP7211 ds7211 ver0.2 apr. 2005 1 dual 150/300ma ldo description the EUP7211 is a dual low dropout linear regulator. the first regulator is capable of sourcing 150ma, while the second regulator can source up to 300ma. the EUP7211 is stable with small ceramic output capacitors. the performance of EUP7211 is optimized for battery power systems to deliver low noise, low dropout voltage, low quiescent current and excellent line and load transient response. the EUP7211 is available in fixed output voltages in the 8-pin 3mm ?? 3mm qfn leadless package. typical application features z input voltage range: 2.5v to 5.5v z stable with ceramic output capacitor z 2 ldo outputs: ? output 1-150ma output current ? output 2-300ma output current z low dropout voltage of 100mv@150ma z low quiescent current of 150a z high psrr 70db at 1khz: z thermal shutdown protection z current limit protection z 3mm ?? 3mm qfn-8 package z rohs compliant and 100% lead (pb)-free applications z cellular phones z wireless modems z pdas
preliminary EUP7211 ds7211 ver0.2 apr. 2005 2 block diagram pin configurations part number pin configurations EUP7211 qfn-8 pin description pin pin description v in 1 input voltage of the ldo en1 2 enable input to regulator 1 en2 3 enable input logic, enable high bypass 4 optional bypass capacitor for noise reduction nc 6 no connection gnd 5 ground v out2 7 output of regulator 2: 300ma output current v out1 8 output of regulator 1: 150ma output current
preliminary EUP7211 ds7211 ver0.2 apr. 2005 3 ordering information order number package type markin g operating temperature range EUP7211-1.8/2.8jir1 qfn-8 de xx p7211 -40 c to 125c EUP7211-1.8/2.8jir0 qfn-8 de xx p7211 -40 c to 125c EUP7211-3.3/1.8jir1 qfn-8 hd xx p7211 -40 c to 125c EUP7211-3.3/1.8jir0 qfn-8 hd xx p7211 -40 c to 125c EUP7211 ?????? / ?????? ?? ?? ?? ?? lead free code 1: lead free 0: lead packing r: tape & reel operating temperature range i: industry standard package type j: qfn output voltage option
preliminary EUP7211 ds7211 ver0.2 apr. 2005 4 absolute maximum ratings ? v in ,v en ---------------------------------------------------------------------------------- 0v to 7v ? power dissipation (p d ) ------------------------------------------------------ internally limited ? junction temperature ------------------------------------------------------ -40c to +125c ? storage temperature ------------------------------------------------------ -65c to +150c ? lead temp ------------------------------------------------------------------------------ 260c operating ratings ? v in ------------------------------------------------------------------------------------ 2.5 to 5.5v ? v en -------------------------------------------------------------------------------------- 0v to v in ? junction temperature ------------------------------------------------------ -40c to +125c ? thermal resistance ja (qfn-8) --------------------------------------------------- 60c/w electrical characteristics v in = v out +1.0v, i out =1ma, c out =1f. typical values and limits appear ing in standard typeface are for t j = 25c symbol parameter conditions min typ max units ? v out output voltage accuracy variation from nominal vout -1.5 1.5 % reg line line regulation input range vin=vout+1v to 5.5v -0.2 0.02 0.2 %/v iout=100 a to 150ma(vout 1 & vout 2) 0.7 2 reg load load regulation iout=100 a to 300ma(vout) 1 2.5 % iout=150ma(vout 1) 120 180 v drop dropout voltage iout=300ma(vout 2) 240 350 mv iout 1=iout2=0 150 170 i q ground pin current iout 1=150ma & iout=300ma 250 300 a iq_sd ground pin current in shutdown v en 0.4v ?? 3 5 a psrr ripple rejection freq.=1khz; cout=1.0 f; c byp =10nf 70 db output 1 short to ground 150 340 iout(max) current limit output 2 short to ground 300 580 ma noise output voltage noise cout=1.0 f;c byp =10nf; bw=10~100khz 40 vrms enable input logic low (regulator shutdown) 0.6 v en enable input voltage logic high(regulator enable) 1.8 v v il <0.6v (regulator shutdown) -0.5 0.01 0.5 i en enable input current v ih >1.8v (regulator enable) -0.5 0.01 0.5 a
preliminary EUP7211 ds7211 ver0.2 apr. 2005 5 typical operating characteristics unless otherwise specified, c in =c cout =1f ceramic, c bypass =100nf, v in =v out +1v, i out = 100a t a =25c, enable pin is tied to v in.
preliminary EUP7211 ds7211 ver0.2 apr. 2005 6
preliminary EUP7211 ds7211 ver0.2 apr. 2005 7
preliminary EUP7211 ds7211 ver0.2 apr. 2005 8
preliminary EUP7211 ds7211 ver0.2 apr. 2005 9 application note function description the EUP7211 is a high performance, low quiescent current power management ic consisting of two cap low dropout regulators, a power-on reset (por) circuit and an open-drain driver. the first regulator is capable of sourcing 150ma at output voltages from 1.25v to 5v. the second regulator is capable of sourcing 300ma of current at output voltages from 1.25v to 5v. the second regulator has a por circuit that monitors its output voltage and indicates when the output voltage is within 5% of nominal. the por offers a delay time that is externally programmable with a single capacitor to ground. an open-drain driver completes the power management chipset, offering the capability of driving leds for keypad backlighting in applications such as cellphones. enable 1 and 2 the enable inputs allow for logic control of both output voltages with individual enable inputs. the EUP7211 is turned off by pulling the v en pin low, and turned on by pulling it high. if this feature is not used, the v en pin should be tied to v in to keep the regulator output on at all time. to assure proper operation, the signal source used to drive the v en input must be able to swing above and below the specified turn-on/off voltage thresholds listed in the electrical characteristics section under v il and v ih . external capacitors like any low-dropout regulator, the EUP7211 requires external capacitors for regulator stability. the EUP7211 is specifically designed for portable applications requiring minimum board space and smallest components. these capacitors must be correctly selected for good performance. input capacitor an input capacitance of 1f or greater is required between the EUP7211 input pin and ground (the amount of the capacitance may be increased without limit). this capacitor must be located a distance of not more than 1cm from the input pin and returned to a clean analog ground. any good quality ceramic, tantalum, or film capacitor may be used at the input. output capacitor the EUP7211 is designed specifically to work with very small ceramic output capacitors. a ceramic capacitor (temperature characteristics x7r, x5r, z5u, or y5v) in 1 to 22f range with 5m ? to 500m ? esr range is suitable in the EUP7211 application circuit. the output capacitor must meet the requirement for minimum amount of capacitance and also have an esr (equivalent series resistance) value which is within a stable range (5m ? to 500m ? ) no-load stability the EUP7211 will remain stable and in regulation with no external load. this is specially important in cmos ram keep-alive applications. capacitor characteristics the EUP7211 is designed to work with ceramic capacitors on the output to take advantage of the benefits they offer: for capacitance values in the range of 1f to 4.7f range, ceramic capacitors are the smallest, least expensive and have the lowest esr values (which makes them best for eliminating high frequency noise). the esr of a typical 1f ceramic capacitor is in the range of 20m ? to 40m ? , which easily meets the esr requirement for stability by the EUP7211. the ceramic capacitor?s capacitance can vary with temperature. the capacitor type x7r, which operates over a temperature range of -55c to +125c, will only vary the capacitance to within 15%. most large value ceramic capacitors ( 2.2f) are manufactured with z5u or y5v temperature characteristics. th eir capacitance can drop by more than 50% as the temperature goes from 25c to 85c. therefore, x7r is recommended over z5u and y5v in applications where the ambien t temperature will change significantly above or below 25c. noise bypass capacitor connecting a 0.01f capacitor between the c bypass pin and ground significantly reduces noise on the regulator output. this cap is connected directly to a high impedance node in the bandgap reference circuit. any significant loading on this node will cause a change on the regulated output voltage. for this reason, dc leakage current through this pin must be kept as low as possible for best output voltage accuracy. the types of capacitors best suited for the noise bypass capacitor are ceramic and film. unlike many other ldo?s, addition of a noise reduction capacitor does not effect the load transient response of the device
preliminary EUP7211 ds7211 ver0.2 apr. 2005 10 packaging information qfn-8 note 1. all dimensions are in millimeters, is in degrees 2. m: the maximum allowable corner on the molded plastic body corner 3. dimension d does not include mold protrusions or gate burrs. mold protrusions and gate burrs shall not exceed 0.15mm per side 4. dimension e does not include interterminal mold protrusions or terminal protrusions. interminal mold protrusions and/or terminal protrusions shall not exceed 0.20mm per side 5. dimension b applies to plated terminals. dimension a1 is primarily y terminal plating, but may or may not include a small protrusion of termin al below the bottom surface of the package 6. burr shall not exceed 0.060mm 7. jedec mo-229 symbols dimensions in millimeters min. nom. max. a 0.81 0.9 1.00 a1 0 0.015 0.03 a3 ------ 0.20 ref ------ b 0.25 0.30 0.37 d 2.85 3.00 bsc 3.15 d1 ------ 2.3 bsc ------ e 2.85 3.00 bsc 3.15 e1 ------ 1.5 bsc ------ e ------ 0.65 bsc ----- l 0.25 0.35 0.45 aaa ------ 0.25 ------ bbb ------ 0.10 ------ ccc ------ 0.10 ------ m ------ ------ 0.05 -12 ------ 0
|
